Technicial Specifications
| Maximum Rating | 450 BHP 336 bkW |
| Displacement | 681 in³ 11.15 l |
| Minimum Rating | 325 BHP 242 bkW |
| Governor and Protection | Electronic (ADEM™ A3) Electronic (ADEM™ A3) |
| Aspiration | Turbocharged-Aftercooled Turbocharged-Aftercooled |
| Flywheel and Flywheel Housing | SAE 1 or SAE 2 SAE 1 or SAE 2 |
| Flywheel Teeth | 113 (SAE 1), 138 (SAE 2) 113 (SAE 1), 138 (SAE 2) |
| Rotation from Flywheel End | Counterclockwise Counterclockwise |
| Stroke | 5.51 in 140 mm |
| Bore | 5.12 in 130 mm |
| Emissions | EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA, IMO II EPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA, IMO II |
| Length | 47.3 in 1201 mm |
| Width | 41.6 in 1057 mm |
| Height | 46.3 in 1176 mm |
| Weight | 1967 lb 892.22 kg |
| Lube Oil System - Refill | 9 gal (US) 34 l |
Advantages and Features
Custom Packaging
For any petroleum application, trust Caterpillar to meet your project needs with custom factory generator sets and mechanical packages. Cat engines, generators, controls, radiators, and transmissions can be custom designed and matched in collaboration with our local dealers to create unique solutions. Custom packages are globally supported and are covered by a one year warranty after startup.Transmissions
Caterpillar has a full line of engine-transmission packages that can be fully integrated with your axle, hydraulics, and operator interface. Cat transmissions deliver continuous operation under full load, smooth shifting at any speed, and maximum up time, with unmatched durability and easy maintenance.Full Range of Attachments
Large variety of factory-installed engine attachments reduces packaging timeTesting
Every engine is full-load tested to ensure proper engine performance.Product Support Offered Through Global Cat Dealer
- More than 2,200 dealer outlets
- Cat factory-trained dealer technicians service every aspect of your petroleum engine
- Cat parts and labor warranty
- Preventive maintenance agreements available for repair before-failure options
- S·O·S℠ program matches your oil and coolant samples against Caterpillar set standards to determine: Internal engine component condition, Presence of unwanted fluids, Presence of combustion by-product
Over 80 Years of Engine Manufacturing Experience
Ownership of these manufacturing processes enables Caterpillar to produce high quality, dependable products.Website
For all your petroleum power requirements, visit cat.com/oilandgas.Standard Equipment
-
Air Inlet System
- Turbocharger, mid-mounted
- Air inlet elbow 90°, 104.5 mm (4.11" OD) hose connection
-
Control System
- Electronic governing, PTO speed control
- Programmable ratings
- Cold mode start strategy
- Automatic altitude compensation
- Power compensation for fuel temperature
- Programmable low and high idle and TEL
- Electronic diagnostics and fault logging
- Engine monitoring system — speed, temperature, pressure
- J1939 Broadcast — diagnostic and engine status
-
Cooling System
- Thermostats and housing
- Jacket water pump — gear-driven
- Front water pump inlet
-
Exhaust System
- Exhaust manifold — dry
- Front turbo exhaust
-
Flywheels and Flywheel Housings
- See Mandatory Options
-
Fuel System
- Electronic unit injector
- Fuel filter — secondary, mid-mount, (LH 2 micron high performance)
- Fuel transfer pump — front
- Fuel priming pump — LH mid-mount
-
Lube System
- Crankcase breather
- Oil cooler
- Oil filter — RH
- Oil pan — front sump, 40 L capacity
- Oil filler — LH front
- Oil dipstick — LH mid-mount
- Oil pump
- Oil valve sampling — on oil filter base
-
Power Take-Offs
- Crankshaft pulley and damper — 250 mm (9.84 in), 2 grooves 22.3 mm (.87 in) width
- Hydraulic pump drive — SAE A, 11 tooth
- 1.41:1 drive ratio — counterclockwise rotation (45 lb-ft capacity)
-
General
- Vibration damper
- Paint — Cat yellow
- Lifting eyes
- Automatic variable timing, electronic
- Electronic installation kit (connectors, pins, sockets)
- Literature
-
Mandatory Options
- Flywheel housing or rear PTO
- Throttle position sensor
- Primary filter/water separator
Optional Equipment
-
Air Compressor
- Expansion chamber
- Governors
- Fittings
-
Air Inlet System
- Air cleaners
- Precleaners
- Turbo air inlet
- Air lines
-
Belt-Driven Accessories
- Refrigerant compressor and mounting
-
Charging System
- Charging alternators
- Alternator mountings
- Alternator guard
- Alternator accessories
-
Control System
- Connection
-
Cooling System
- Radiator — installed
- Fan drive f/u/w Caterpillar installed radiator
- Fan drive pulleys f/u/w customer-supplied radiators
- Coolant conditioner
- Water lines — pump inlet
- Fan drive mountings
- Fan height instructions
- Fan adapters for suction fans
- Fan adapters for blower fans
- Suction fans
- Blower fans
- Coolant level sensor
- Aftercooler lines
-
Exhaust System
- Muffler
- Flexible fitting
- Elbows
- Straight exhaust adapter
- Flange
- Pipe
- Rain cap
- Clamp
-
Fuel System
- Fuel lines
- Fuel cooler
- Fuel fitting — fuel return and supply connections
- Flexible fuel lines
-
Instrumentation
- Gauges and instrument panels
- Voltmeters
- Gauge mounting
- Ammeter
-
Lube System
- Oil pan
- Oil pan drain
- Oil level gauges
- Oil filter — bypass
- Oil filter — remote
- Lubricating oil
- Oil filler
- Fumes disposal
-
Mounting System
- Front and rear engine supports
- Structural steel base
-
Power Take-Offs
- Crankshaft pulleys
- Crankshaft pulley — stack-on
- Output flange
- Flywheel stub shaft
- Front stub shaft
- Hydraulic pump drive
- Hydraulic pumps — front
- Hydraulic pumps — rear
- Enclosed Clutch
- Clutch Support
-
Protection System
- Air shutoff
- Air shutoff switch
-
Starting System
- Electric starting motors — 12 Volt, 24 Volt
- Starting aids
- Battery sets — 24 Volt, dry
- Battery cable
- Battery rack
-
Transmission Arrangement
- Transmission cooler
