Güç Sistemleri

Standart Donanımlar

• AIR INLET SYSTEM
  • Separate circuit after-cooled (SCAC)
  • Air cleaner
  • Turbocharger, jacket water cooled
  • Turbocharger inlet, 152 mm (6 in) OD straight connection

• CONTROL SYSTEM
  • Programmable Low Idle (550 - 750 rpm)
  • Programmable High Idle Limit for WOSR Ratings
  • Electronic diagnostics and fault logging
  • Engine and transmission monitoring (speed, temperature, pressure)
  • Electronic fuel/air ratio control
  • Engine Protection Mode for extended ambient conditions
  • 70-pin customer connector
  • Throttle Input signal options
  • 0 - 5 Volts
  • 4 - 20 mA
  • PWM (Pulse Width Modulated)

• COOLING SYSTEM
  • Separate Circuit After-Cooling (SCAC) for both HEX and Keel cooled engines
  • Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines
  • SCAC pump, gear driven
  • Jacket water pump, gear driven
  • Sea water pump, bronze impeller, gear driven, when selected for Hex cooled engines
  • Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection
  • Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt
  • SCAC and JW shunt tanks for maintaining proper pump inlet pressures

• EXHAUST SYSTEM
  • Water-cooled exhaust manifold & turbocharger
  • 4 Bolt 130 mm (5.12 in) diameter flanged outlet

• FLYWHEELS & FLYWHEEL HOUSINGS
  • SAE standard rotation (CCW facing exciter end)
  • Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth

• FUEL SYSTEM
  • Duplex Fuel Filters, Spin-on, RH & LH service
  • Fuel connections size: r driven
  • Plate-type fuel cooler installed behind Aftercooler Shunt Tank
  • Fuel transfer pump, gear driven
  • Manual fuel priming pump
  • Hybrid fuel line design

• LUBE SYSTEM
  • Simplex Oil Filters, RH or LH service
  • Deep sump oil pan
  • RH or LH service oil filler locations
  • RH or LH service dipstick
  • Oil pump, gear driven

• MOUNTING SYSTEM
  • Front support - 33 inches wide

• POWER TAKE-OFFS
  • Front Poly-V groove pulley (Quantity 1) for auxiliary drives

• GENERAL
  • Common electrical bonding point
  • Engine does not ship with zinc components

İsteğe Bağlı Donanımlar

• EXHAUST SYSTEM
  • Dry Elbows
  • Flexible Fitting
  • Flange
  • Muffler
  • Muffler Spark Arresting

• AIR INLET SYSTEM
  • Air Inlet Adapter

• CHARGING SYSTEM
  • Battery Chargers
  • Charging Alternators
  • Ammeter

• CONTROL SYSTEM
  • Load Sharing Attachment
  • Instrument Panels
  • Caterpillar Alarm Protection
  • Fuel and Oil Shielding

• FUEL SYSTEM
  • Water Separator

• GENERAL
  • Fumes Disposal System

• INSTRUMENTATION
  • Instrument Panels
  • OEM Wiring Harness
  • Engine to Engine Harness
  • Gauges
  • Transmission Sensors
  • Exhaust Temperature Sensors

• LUBE SYSTEM
  • Duplex Oil Filters
  • Sump Pump

• POWER TAKE-OFFS
  • Rear Hydraulic Pump Drive

• STARTING SYSTEM
  • Electric Starting Motors - Single 24 Volt
  • Air Starting Motor
  • Dual Starting Motors (Electric and Air)
  • Air Start Accessories
  • Starting Aids - JW Heaters
  • Battery Sets - 24 Volt - Dry

• MOUNTING SYSTEM
  • Front Support
  • Rear Support
  • Isolators Mounts
  • Adapter Kits

• PACKING
  • Engine Protective Cover
  • Storage Preservation
  • Export Packing